manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

PCV SYSTEM

INSPECTION

NOTE:
Be sure to check that there is no obstruction in PCV valve or
its hoses before checking engine idle speed/IAC duty for ob-
structed PCV valve or hose hampers its accurate checking.

1) Check hoses for connection, leakage, clog, and deterioration.

Replace as necessary.

2) Disconnect PCV valve from cylinder head cover and plug head

cover hole.

1. Breather hose
2. PCV valve
3. PCV hose
A. Cylinder head
B. Cleaner outlet hose
C. Intake manifold

3) Run engine at idle.
4) Place your finger over end of PCV valve to check for vacuum.

If there is no vacuum, check for clogged valve and hose. Re-
place as necessary.

5) After checking vacuum, stop engine and remove PCV valve.

Shake valve and listen for the rattle of check needle inside the
valve. If valve does not rattle, replace valve.

6) After checking, connect PCV valve, PCV hose and clamp se-

curely.

ENGINE AND EMISSION CONTROL SYSTEM

6E-79

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jabra TOUR Get Started preview
TOUR
Бренд: Jabra Страницы: 10
Jeda Wireless Pad Manual preview
Wireless Pad
Бренд: Jeda Страницы: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 496
Tamiya KO PROPO RTF 2002 ESC Manual preview
KO PROPO RTF 2002 ESC
Бренд: Tamiya Страницы: 2
Pacbrake C44059 Installation Manual preview
C44059
Бренд: Pacbrake Страницы: 14
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Бренд: KRAFTWERK Страницы: 2
PEUGEOT 407 2010 Manual preview
407 2010
Бренд: PEUGEOT Страницы: 249
Van Guard VG273 Fitting Instructions preview
VG273
Бренд: Van Guard Страницы: 3
Opel 2013 Corsa Brochure & Specs preview
2013 Corsa
Бренд: Opel Страницы: 32
Qeedon Higlow Series Product Instruction preview
Higlow Series
Бренд: Qeedon Страницы: 2
cam PFF Series Operating Manual preview
PFF Series
Бренд: cam Страницы: 28
GARO Wallbox GLB Quick Start Manual preview
Wallbox GLB
Бренд: GARO Страницы: 15
Thetford SANICON TURBO 300 Operating Instructions Manual preview
SANICON TURBO 300
Бренд: Thetford Страницы: 25
PUTCO Molle Panels Assembly And Instruction Manual preview
Molle Panels
Бренд: PUTCO Страницы: 2
MBRP 0130717 Assembly preview
0130717
Бренд: MBRP Страницы: 5
Waeco MAGIC WATCH MWE-850-4XXL Installation And Operating Manual preview
MAGIC WATCH MWE-850-4XXL
Бренд: Waeco Страницы: 228
Edelbrock 71883 Installation Instructions preview
71883
Бренд: Edelbrock Страницы: 4
Bracketron MULTI VEHICLE MOUNT MVM-45-05 Installation Manual preview
MULTI VEHICLE MOUNT MVM-45-05
Бренд: Bracketron Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды