manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

AIR BAG SYSTEM

10B-47

AIR BAG (INFLATOR) MODULE DISPOSAL

WARNING:
Failure to follow proper air bag (inflator) module disposal procedures can result in air bag deploy-
ment which may cause personal injury.
Undeployed air bag (inflator) module must not be disposed of through normal refuse channels.
The undeployed air bag (inflator) module contain substances that can cause severe illness or per-
sonal injury if the sealed container is damaged during disposal.

Do not dispose of the live (undeployed) air bag (inflator) module(s).
The method employed depends upon the final disposition of the particular vehicle, as noted in DEPLOYMENT
OUTSIDE VEHICLE and DEPLOYMENT INSIDE VEHICLE in this section.

Deployment Outside Vehicle

disposing of the air bag (inflator) module(s) only (i.e., the vehicle itself will

. . . . . . . . 

be used again).

Deployment Inside Vehicle

scrapping the entire vehicle including the air bag (inflator) module(s).

. . . . . . . . . . 

WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.

To avoid an accidental deployment, this work should be performed by no more than one person.

The procedure should be followed strictly as described here.

Be sure to read SERVICE PRECAUTIONS in this section beforehand.

Never connect deployment harness to any power source before connecting deployment harness
to the air bag (inflator) module. Deployment harness shall remain shorted and not be connected
to a power source until the air bag is to be deployed.

Since the smoke is produced when air bag is deployed, select a well-ventilated area.

The air bag (inflator) module will immediately deploy when a power source is connected to it. Wear
safety glasses throughout this entire deployment and disposal procedure.

Wear suitable ear protection when deploying air bag. Also, advise those who are in the area close
to deployment site to wear suitable ear protection.

Do not deploy two or more air bag system components (air bag (inflator) modules) at the same
time.

DEPLOYMENT OUTSIDE VEHICLE

Use this procedure when the vehicle itself is used again (only the air bag (inflator) module(s) are disposed of).

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Бренд: Jeep Страницы: 608
UMBRA RIMORCHI 39030 Installation Instructions Manual preview
39030
Бренд: UMBRA RIMORCHI Страницы: 18
iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Бренд: iDataLink Страницы: 99
Mitsubishi 1998 FTO Technical Information Manual preview
1998 FTO
Бренд: Mitsubishi Страницы: 160
Cadillac 2004 CTS Owner'S Manual preview
2004 CTS
Бренд: Cadillac Страницы: 442
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Бренд: Kolpin Outdoors Страницы: 6
Schartec CR 4 Manual preview
CR 4
Бренд: Schartec Страницы: 2
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Бренд: Actia Страницы: 37
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Бренд: Honda Страницы: 4
Pro-gard SAFESTOP SS0005 Installation Manual preview
SAFESTOP SS0005
Бренд: Pro-gard Страницы: 4
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
Dometic LMC Eriba Nova Service Manual preview
LMC Eriba Nova
Бренд: Dometic Страницы: 24
Ford F-250 Super Duty 2022 Owner'S Manual preview
F-250 Super Duty 2022
Бренд: Ford Страницы: 740
Prorack K374 Manual preview
K374
Бренд: Prorack Страницы: 14
Rydeen BSS2 Owner'S Manual preview
BSS2
Бренд: Rydeen Страницы: 14
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Car-Interface CI-RL4-R40 Manual preview
CI-RL4-R40
Бренд: Car-Interface Страницы: 25
Valeo MBHL Operating Manual preview
MBHL
Бренд: Valeo Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды