manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

Inspect valve stem end face for pitting and wear. If pitting or wear
is found there, valve stem end may be resurfaced, but not so
much as to grind off its chamfer. When it is worn so much that
its chamfer is gone, replace valve.

Seating contact width:
Create contact pattern on each valve in the usual manner, i.e.,
by giving uniform coat of marking compound to valve seat and
by rotatingly tapping seat with valve head. Valve lapper (tool
used in valve lapping) must be used.

Pattern produced on seating face of valve must be a continuous
ring without any break, and the width of pattern must be within
specified range.

6A-40

ENGINE MECHANICAL

Standard seating width revealed

In

1.1 – 1.3 mm

g

by contact pattern on valve face

Ex

(0.0433 – 0.0512 in.)

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Falcon 1990 Installation Instructions And Specifications preview
1990
Бренд: Falcon Страницы: 8
Barker 25895 Owner'S Instructions preview
25895
Бренд: Barker Страницы: 2
BESAFE iZi Flex Manual preview
iZi Flex
Бренд: BESAFE Страницы: 4
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Бренд: Chrysler Страницы: 1534
Inbay 241170-53-1 Installation Manual preview
241170-53-1
Бренд: Inbay Страницы: 20
Hudson 1933 Eight Owner'S Manual preview
1933 Eight
Бренд: Hudson Страницы: 34
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Бренд: MULTILIFT Страницы: 62
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Бренд: IOGear Страницы: 38
Audiovox Prestige 128-8602 Installation Manual preview
Prestige 128-8602
Бренд: Audiovox Страницы: 8
Motoalliance Denali MA11737 Manual preview
Denali MA11737
Бренд: Motoalliance Страницы: 4
Webasto HOLLANDIA 700 - 20 Series Service Manual preview
HOLLANDIA 700 - 20 Series
Бренд: Webasto Страницы: 30
Ford TRANSIT 2015 Quick Reference Manual preview
TRANSIT 2015
Бренд: Ford Страницы: 8
ACV 381190-37-1 Installation Manual preview
381190-37-1
Бренд: ACV Страницы: 2
iDataLink BLADE-AL-HK4-EN Install Manual preview
BLADE-AL-HK4-EN
Бренд: iDataLink Страницы: 35
Edelbrock 71883 Installation Instructions preview
71883
Бренд: Edelbrock Страницы: 4
Baseus CRJS01 User Manual preview
CRJS01
Бренд: Baseus Страницы: 5
Mercedes-Benz A-Class 2020 Operator'S Manual preview
A-Class 2020
Бренд: Mercedes-Benz Страницы: 434
ZeroRPM IMS2 Operator'S Manual preview
IMS2
Бренд: ZeroRPM Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды