manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

BULB REPLACEMENT

WARNING:
Don’t touch when the bulb is hot.

1. Bulb
2. Spring

1) Disconnect negative (–) cable at battery.
2) Disconnect harness from bulb.
3) Remove socket cover and bulb.
4) Replace bulb and assemble all removed parts.

HEADLIGHT AIMING WITH SCREEN

NOTE:

Unless otherwise obligated by local regulations, adjust
headlight aiming according to following procedure.

After replacing headlight, be sure to adjust aiming.

Before adjustment, make sure the following.
a) Place vehicle on a flat surface in front of blank wall (screen)

ahead of headlight surface.

Clearance “a”: 10 m (32.8 ft.)

b) Adjust air pressure of all tires to a specified value respectively.
c) Bounce vehicle body up and down by hand to stabilize suspen-

sion.

d) Carry out with one driver aboard.

Driver’s weight: 75 kg (165 Ib)

Adjustment

1) Check to see if hot spot (high intensity zone) of each main (low)

beam axis falls as illustrated.

Clearance “H”: Approx. 130 mm (5.15 in.)

2) If headlight aiming is not set properly, align it to specification by

adjusting aiming screw and aiming gear.

X - X: Horizontal center line of headlights bulb
A - A: Vertical center line of left headlight bulb
B - B: Vertical center line of right headlight bulb

1. Headlight ass’y
2. Aiming (for right/left adjustment)
3. Aiming (for up/down adjustment)

1. Screen

LH steering vehicle shown

BODY ELECTRICAL SYSTEM

8-17

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Whispbar K783W Fitting Instructions Manual preview
K783W
Бренд: Whispbar Страницы: 16
Honda 2004 S2000 Owner'S Manual preview
2004 S2000
Бренд: Honda Страницы: 208
Toyota AURION 2013 Owner'S Manual preview
AURION 2013
Бренд: Toyota Страницы: 371
Dodge 8W-30 Wiring Diagram preview
8W-30
Бренд: Dodge Страницы: 24
AA Products RB0007 Instruction Manual preview
RB0007
Бренд: AA Products Страницы: 6
ideus VV950 User Manual preview
VV950
Бренд: ideus Страницы: 159
Pyle PLDCP3 User Manual preview
PLDCP3
Бренд: Pyle Страницы: 2
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Бренд: APS Страницы: 3
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Бренд: N-Com Страницы: 36
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Бренд: Lexus Страницы: 830
Yakima K974 Manual preview
K974
Бренд: Yakima Страницы: 11
Toyota 2011 Camry SE V6 Brochure & Specs preview
2011 Camry SE V6
Бренд: Toyota Страницы: 33
Cadillac Escalade 2004 Escalade ESV Owner'S Manual preview
Escalade 2004 Escalade ESV
Бренд: Cadillac Страницы: 472
Webasto H300 comfort Operating Instructions Manual preview
H300 comfort
Бренд: Webasto Страницы: 44
CARFACE CF145962E Instruction Manual preview
CF145962E
Бренд: CARFACE Страницы: 16
LedGlow Advanced Million Color Installation Instructions preview
Advanced Million Color
Бренд: LedGlow Страницы: 4
Nav TV MOST-HUR31 Manual preview
MOST-HUR31
Бренд: Nav TV Страницы: 8
Haltech NEXUS R3 Quick Start Manual preview
NEXUS R3
Бренд: Haltech Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды