manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

1) Assemble low speed synchronizer hub (1), sleeve (2), springs

(4) and keys (3).
a) Slide hub in sleeve so that punch marked side of hub and

groove machined side of sleeve face the same direction.

b) Insert keys in hub slots with depression side of keys face

center of hub.

c) Install springs to internal circle of key locations with spring

end gaps apart at angles about 120 degrees each other.

Synchronizer spring installation position
: A = B

5. Groove
6. Punch mark
[C]: 2nd gear side (forward)

2) Install needle bearing, 2nd gear (3) and 2nd synchronizer ring

to main shaft.

3) [In the case of press-fitting hub]

Using special tool, puller and hydraulic press, drive in low speed
synchronizer sleeve and hub assembly (1) with punch marked
side of hub directed to backward (low gear side).

Special Tool
(A): 09924-07710

NOTE:
Check free rotation of 2nd gear after press-fitting sleeve
and hub assembly.

[In the case of loose-fitting hub]
Install low speed synchronizer sleeve and hub assembly (1)
with punch marked side of hub directed to backward (low gear
side).

CAUTION:
Make sure synchronizer ring key slots (2) must be
aligned with keys while press-fitting sleeve and hub
assembly. Otherwise synchronizer ring may be dam-
aged.

MANUAL TRANSMISSION

7A-19

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

TrailFX A4012S Installation Instructions Manual preview
A4012S
Бренд: TrailFX Страницы: 6
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Бренд: GMC Страницы: 425
Gator GX5HDKT User Manual preview
GX5HDKT
Бренд: Gator Страницы: 8
FAAFTECH FT-VF-HND2 Installation Manual preview
FT-VF-HND2
Бренд: FAAFTECH Страницы: 8
AutoMaxi AXIS XXL Instructions preview
AXIS XXL
Бренд: AutoMaxi Страницы: 2
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Бренд: Harman Kardon Страницы: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Бренд: TATA Motors Страницы: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Бренд: B&G electronics Страницы: 7
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Бренд: mtf TRANSPORT SYSTEM Страницы: 9
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42
E&G Classics Black Ice Mesh Instruction Manual preview
Black Ice Mesh
Бренд: E&G Classics Страницы: 4
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Бренд: IOGear Страницы: 38
Porsche BOXTER - Technical Manual preview
BOXTER -
Бренд: Porsche Страницы: 146
Tobe EPS-LD SafePark Technical Data preview
EPS-LD SafePark
Бренд: Tobe Страницы: 2
Scosche VQ2M Manual preview
VQ2M
Бренд: Scosche Страницы: 32
Curt Manufacturing 58987 Installation Manual preview
58987
Бренд: Curt Manufacturing Страницы: 4
Jeep WG Grand Cherokee 2002 Service Manual preview
WG Grand Cherokee 2002
Бренд: Jeep Страницы: 74
Adaptiv Mini CAM-MB6-AD User Manual preview
CAM-MB6-AD
Бренд: Adaptiv Mini Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды