manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

IMPORTANT

WARNING/CAUTION/NOTE

Please read this manual and follow its instructions
carefully. To emphasize special information, the
words 

WARNING

, 

CAUTION

 and 

NOTE

 have spe-

cial meanings. Pay special attention to the messages
highlighted by these signal words.

WARNING:
Indicates a potential hazard that could result in
death or injury.

CAUTION:
Indicates a potential hazard that could result in
vehicle damage.

NOTE:
Indicates special information to make mainte-
nance easier or instructions clearer.

WARNING:
This service manual is intended for authorized
SUZUKI dealers and qualified service mechan-
ics only. Inexperienced mechanics or mechan-
ics without the proper tools and equipment may
not be able to properly perform the services de-
scribed in this manual.
Improper repair may result in injury to the me-
chanic and may render the vehicle unsafe for
the driver and passengers.

WARNING:
For vehicles equipped with Supplemental Re-
straint (Air Bag) System:

D

Service on or around the air bag system com-
ponents must be performed only by an autho-
rized SUZUKI dealer. Please observe all
WARNINGS, CAUTIONS and “Service Precau-
tions” under “On-Vehicle Service” in SEC-
TION 10B before performing service on or
around the air bag system components or wir-
ing. Failure to follow WARNINGS could result
in unintentional activation of the system or
could render the system inoperative. Either of
these two conditions may result in serve inju-
ry.

D

If the air bag system and another vehicle sys-
tem both need repair, SUZUKI recommends
that the air bag system be repaired first, to
help avoid unintentional activation of the air
bag system.

D

Do not modify the steering wheel, instrument
panel or any other air bag system component.
Modifications can adversely affect air bag
system performance and lead to injury.

D

If the vehicle will be exposed to temperatures
over 93

°

C (200

°

F) (for example, during a paint

baking process), remove the air bag system
components (air bag (inflator) modules, SDM
and seat belt pretensioner (if equipped)) be-
forehand to avoid component damage or
unintended activation of the system.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Бренд: Suzuki Страницы: 16
Cadillac ESCALADE - BROCHURE 2009 Personalization Manual preview
ESCALADE - BROCHURE 2009
Бренд: Cadillac Страницы: 24
Cadillac Escalade Personalization Manual preview
Escalade
Бренд: Cadillac Страницы: 20
Cadillac Escalade 2016 Convenience/Personalization Manual preview
Escalade 2016
Бренд: Cadillac Страницы: 20
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Бренд: FABBRI PORTATUTTO Страницы: 2
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Бренд: GMC Страницы: 425
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Бренд: BrandMotion Страницы: 8
TATA Motors tigor Owner'S Manual preview
tigor
Бренд: TATA Motors Страницы: 159
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Бренд: Enduro Страницы: 48
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Бренд: Safe Fleet Страницы: 12
JKS OGS125 Installation Instructions preview
OGS125
Бренд: JKS Страницы: 3
Volvo B13R Driver'S Handbook Manual preview
B13R
Бренд: Volvo Страницы: 24
Jeep 2014 Grand Cherokee SRT8 Owner'S Manual preview
2014 Grand Cherokee SRT8
Бренд: Jeep Страницы: 596
Skoda 1K0 051 437 Assembly Instructions preview
1K0 051 437
Бренд: Skoda Страницы: 4
Yakima K1249 Instructions Manual preview
K1249
Бренд: Yakima Страницы: 9
Motoalliance Denali MA11705 Manual preview
Denali MA11705
Бренд: Motoalliance Страницы: 5
DFI VC230-BT Installation Manual preview
VC230-BT
Бренд: DFI Страницы: 6
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Бренд: ECS Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды