manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

ENGINE MECHANICAL

6A-1

SECTION 6A

ENGINE MECHANICAL

WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an
authorized SUZUKI dealer. Refer to AIR BAG SYSTEM COMPONENTS AND WIRING LOCATION
VIEW of GENERAL DESCRIPTION in air bag system section in order to confirm whether you are
performing service on or near the air bag system components or wiring. Please observe all WARN-
INGS and SERVICE PRECAUTIONS of ON-VEHICLE SERVICE in air bag system section before per-
forming service on or around the air bag system components or wiring. Failure to follow
WARNINGS could result in unintentional activation of the system or could render the system inop-
erative. Either of these two conditions may result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to
the LOCK position and negative cable is disconnected from the battery. Otherwise, the system
may be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

CONTENTS

GENERAL DESCRIPTION

6A- 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ENGINE

6A- 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ENGINE LUBRICATION

6A- 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ON-VEHICLE SERVICE

6A- 4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

COMPRESSION CHECK

6A- 4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ENGINE VACUUM CHECK

6A- 5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

OIL PRESSURE CHECK

6A- 6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

VALVE LASH (CLEARANCE)

6A- 7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

AIR CLEANER ELEMENT

6A- 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

CYLINDER HEAD COVER

6A- 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

THROTTLE BODY AND INTAKE MANIFOLD

6A-11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

EXHAUST MANIFOLD

6A-14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

TIMING BELT AND BELT TENSIONER

6A-15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

OIL PAN AND OIL PUMP STRAINER

6A-20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

OIL PUMP

6A-23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ROCKER ARMS, ROCKER ARM SHAFT AND CAMSHAFT

6A-27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

VALVES AND CYLINDER HEAD

6A-35

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

PISTON, PISTON RINGS, CONNECTING RODS AND CYLINDERS

6A-48

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

UNIT REPAIR OVERHAUL

6A-58

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ENGINE ASSEMBLY

6A-58

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

MAIN BEARINGS, CRANKSHAFT AND CYLINDER BLOCK

6A-62

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

TIGHTENING TORQUE SPECIFICATIONS

6A-74

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

SPECIAL TOOLS

6A-75

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

REQUIRED SERVICE MATERIALS

6A-76

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

NOTE:
For what each abbreviation stands for (i.e., full term), refer to SECTION 0A.

6A

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Camcar 2155 Fitting Instructions preview
2155
Бренд: Camcar Страницы: 2
Jeep Compass Owner'S Handbook Manual preview
Compass
Бренд: Jeep Страницы: 322
Jeep Compass Repair Manual preview
Compass
Бренд: Jeep Страницы: 341
Jeep Compass Operating Information Manual preview
Compass
Бренд: Jeep Страницы: 310
Jeep Compass Information Manual preview
Compass
Бренд: Jeep Страницы: 189
Jeep Compass Review preview
Compass
Бренд: Jeep Страницы: 26
Jeep Compass Overview preview
Compass
Бренд: Jeep Страницы: 21
Ecco Gemineye EC2014-C Installation Instructions Manual preview
Gemineye EC2014-C
Бренд: Ecco Страницы: 10
Ecco Reflex 5500 Series Installation And Operating Instructions Manual preview
Reflex 5500 Series
Бренд: Ecco Страницы: 12
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Бренд: Jeep Страницы: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Бренд: Jeep Страницы: 80
Parrot CK 3000 Evolution Specifications preview
CK 3000 Evolution
Бренд: Parrot Страницы: 2
Subaru SPLASH GUARD Installation Manual preview
SPLASH GUARD
Бренд: Subaru Страницы: 3
Mercedes-Benz GUARD S 500 Supplement To Operators Manual preview
GUARD S 500
Бренд: Mercedes-Benz Страницы: 30
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Бренд: CITROEN Страницы: 52
Yakima Whispbar K887W Fitting Instructions Manual preview
Whispbar K887W
Бренд: Yakima Страницы: 19
Nav TV UCI-11C NTV-KIT331 User Manual preview
UCI-11C NTV-KIT331
Бренд: Nav TV Страницы: 4
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Бренд: Curt Manufacturing Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды