manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

ENGINE AND EMISSION CONTROL SYSTEM

6E-25

STEP

ACTION

YES

NO

3

1) Stop engine.
2) With ignition switch OFF position, disconnect

ECM electrical connectors and oxygen sensor
electrical connector.

3) Check “R” and “Bl” wires for open or short.
Are “R” and “Bl” wires in good condition?

Go to Step 4.

Repair or replace.

4

1) Substitute a known-good oxygen sensor. Refer

to “Oxygen Sensor Removal and Installation”.

2) Connect ECM electrical connectors and oxygen

sensor electrical connector.

3) Install SUZUKI scan tool.
4) Start engine.
5) Run engine to normal operating temperature.
6) Maintain engine speed at 2000RPM for 60 se-

conds.

7) Using data list function of SUZUKI scan tool,

monitor oxygen sensor output voltage “02S”
with engine running at 2000RPM.

Does voltage switch below and above 0.55V?

Faulty oxygen sensor.

Poor connection of ECM

connector terminal or ox-

ygen sensor connector

terminal.

If OK, substitute a

known-good ECM and

recheck.

NOTE:
Upon completion of inspection and repair work, perform “DTC Confirmation Procedure” in this section and
confirm that the trouble has been corrected.

Fig. for Step 2, 4

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Lancia Delta Owner'S Handbook Manual preview
Delta
Бренд: Lancia Страницы: 276
T-Tech TT100 User Manual preview
TT100
Бренд: T-Tech Страницы: 38
Camcar 40000 Manual preview
40000
Бренд: Camcar Страницы: 6
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Бренд: Napoli Страницы: 20
Barker 25895 Owner'S Instructions preview
25895
Бренд: Barker Страницы: 2
Kia CADENZA 2019 Features & Functions Manual preview
CADENZA 2019
Бренд: Kia Страницы: 54
Metra Electronics 99-9001 Installation Instructions preview
99-9001
Бренд: Metra Electronics Страницы: 2
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Бренд: CITROËN Страницы: 301
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Бренд: BendPak Страницы: 104
Whispbar K448W Fitting Instructions Manual preview
K448W
Бренд: Whispbar Страницы: 15
Honda 2010 Civic Sedan Owner'S Manual preview
2010 Civic Sedan
Бренд: Honda Страницы: 390
HAUL MASTER 41782 Assembly And Operating Instructions Manual preview
41782
Бренд: HAUL MASTER Страницы: 8
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Бренд: RAM Страницы: 174
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Бренд: Mobility Networks Страницы: 52
GReddy 12519101 Instruction Manual preview
12519101
Бренд: GReddy Страницы: 12
Mercedes-Benz Vito Taxi 2011 Operation Manual preview
Vito Taxi 2011
Бренд: Mercedes-Benz Страницы: 10
Kuda 293950 Installation Instruction preview
293950
Бренд: Kuda Страницы: 3
AL-KO 605 363 Operating Instructions Manual preview
605 363
Бренд: AL-KO Страницы: 88

Бренды по названию

Популярные бренды

Загрузить еще бренды