Toyota PK3B1-34H5H Скачать руководство пользователя страница 1

Страница: 1 / 11

TOYOTA TUNDRA 2016

TONNEAU COVER

Preparation

Page 1 of 11 pages

Issue: C 04/18/2017

DIO

Part Number:
PU100-3415S-01, PK3B1-34H5H (Short)
PU100-3415R-01, PK3B1-34H6H (Reg.)
PU100-3415L-01, PK3B1-34H8H (Long)

Kit Contents

Item #

Quantity Reqd. Description

1 1

Tonneau

Cover

Side Rails (1 left, 1 right)

Drain

Tubes

4 1

Hardware

Bag

Hardware Bag Contents

Item #

Quantity Reqd. Description

1 1

User

Manual

2 1

Clamp

Bracket

(10pc Short Bed, 12pc Regular
Bed, 16pc Long Bed)

T30 Torx, M6 x 1.0 x 30mm
Mounting Hardware
(10pc Short Bed, 12pc Regular
Bed, 16pc Long Bed)

Foam Seal Roll

5 1

Hex

Key

Additional Items Required For Installation

Item #

Quantity Reqd. Description

Bed Rails (if the vehicle is not
already equipped)

Conflicts

Bed Divider (PT767 34070) & Bed Liners that are not
compatible with Toyota accessory rails
GoPro® mount

General Applicability

All Tundra models with accessory bed rails

Recommended Sequence of Application

Item #

Accessory

1 Bed

Liner

2 Tonneau

Cover

3 Accessory

Rails

*Mandatory

Recommended Tools

Personal & Vehicle
Protection

Notes

Safety Glasses

Wrist & Belt Buckle
Protection

Special Tools

Notes

Installation Tools

Notes

Torx Socket

T-30 (Hardened), 3/8” Drive

Torque Wrench

200 N-m, 150 in-lbf, 3/8”
Drive

Ratchet 3/8”

Drive

Ratchet Extension

Short, 3/8” Drive

Drill
Drill Bit

3/4” dia.

Tape Measure

Scissors
Screwdriver Phillips

Plastic Mallet

Special Chemicals

Notes

Vehicle Service Parts

(may be required for reassembly)

Item #

Quantity Reqd. Description

Legend

STOP:

Damage to the vehicle may occur. Do not

proceed until process has been complied with.

OPERATOR SAFETY:

Use caution to avoid risk of

injury.

CAUTION:

A process that must be carefully observed

in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.

TOOLS & EQUIPMENT:

Used in Figures calls out the

specific tools and equipment recommended for this
process.

REVISION MARK:

This mark highlights a change in

installation with respect to previous issue.

SAFETY TORQUE:

This mark indicates that torque is

related to safety.

Содержание PK3B1-34H5H












Результаты поиска

Содержание PK3B1-34H5H

Отзывы:

Похожие инструкции для PK3B1-34H5H

Бренды по названию

Популярные бренды

Toyota PK3B1-34H5H, Руководство по установке

Результаты поиска

Содержание PK3B1-34H5H

Отзывы:

Похожие инструкции для PK3B1-34H5H

Бренды по названию

Популярные бренды