Toyota PK3B1-34H5H Скачать руководство пользователя страница 4

Страница: 4 / 11

TOYOTA TUNDRA 2016

TONNEAU COVER

Procedure

Page 4 of 11 pages

Issue: C 04/18/2017

DIO

(d)

Align the slots in the clamp brackets with the

threaded holes in truck bed sides and install

the supplied mounting bolts (Fig. 2-4). Do

not fully tighten them at this time.

NOTE:

To ensure proper alignment of the driver

and passenger side pins, make sure that both side

rails are placed exactly the same (Fig. 2-5).

(e)

Tighten and torque the mounting bolts to 7.5

N-m (66.5 in-lbf), being sure to hold the rail

in place and PUSH the side rail DOWN

against the bed caps as the clamp is tightened

(Fig. 2-6).

Torque: 7.5 N-m (66.5 in-lbf)

NOTE:

The top of the rail must contact the truck

bed side wall to ensure a good seal (Fig. 2-7).

CAUTION:

If the vehicle is equipped with a

Toyota bed liner, ensure that the liner is not

sandwiched between the clamps and the truck

bed.

Fig. 2-4

T-30 Torx socket, ratchet & extension

Fig. 2-6

T-30 Torx socket & torque wrench

Fig. 2-7

Fig. 2-5

Tape measure

1 inch

Содержание PK3B1-34H5H












Результаты поиска

Содержание PK3B1-34H5H

Отзывы:

Похожие инструкции для PK3B1-34H5H

Бренды по названию

Популярные бренды

Toyota PK3B1-34H5H, Руководство по установке

Результаты поиска

Содержание PK3B1-34H5H

Отзывы:

Похожие инструкции для PK3B1-34H5H

Бренды по названию

Популярные бренды