Toyota PK3B1-34H5H Скачать руководство пользователя страница 5

Страница: 5 / 11

TOYOTA TUNDRA 2016

TONNEAU COVER

Procedure

Page 5 of 11 pages

Issue: C 04/18/2017

DIO

(f)

Align the slide-nut at the front of the side rail

so that the set screw aligns with the hole in

the rail (Fig. 2-8).

(g)

Slowly tighten the set screw with the

provided hex key against the clamp bracket

until the side rail is level (Fig. 2-9).

NOTE:

Do not overtighten the set screw such

that the side rail is no longer level.

(h)

Install the drain tubes (2) onto the drain caps

(Fig. 2-10).

NOTE:

Make sure the tube covers all the three

lines around the drain cap.

NOTE:

If the vehicle is NOT equipped with a

Toyota bed liner or is equipped with a

spray-on

bed liner

, continue to Step 2(i). If the vehicle is

equipped with a Toyota bed liner, skip to Step

2(m).

(i)

Remove the outermost drain plugs.

(j)

Drill a 3/4" hole in each plug.

NOTE:

Create the drain hole towards the bottom

of the plug/vehicle for better routing.

Fig. 2-8

Hex key

Fig. 2-9

Hex key

Fig. 2-10

Содержание PK3B1-34H5H












Результаты поиска

Содержание PK3B1-34H5H

Отзывы:

Похожие инструкции для PK3B1-34H5H

Бренды по названию

Популярные бренды

Toyota PK3B1-34H5H, Руководство по установке

Результаты поиска

Содержание PK3B1-34H5H

Отзывы:

Похожие инструкции для PK3B1-34H5H

Бренды по названию

Популярные бренды