![background image](http://html1.mh-extra.com/html/ducati/999r-2006/999r-2006_repair-manual_2537638089.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Uso e manutenzione
Use and Maintenance operations
sezione / section
D 4
17
999R Aggiornamento/Update
- M.Y. 2006 - edizione/edition 00
Sostituzione liquido
raffreddamento
Attenzione
Questa operazione va
effettuata a motore freddo.
L'operazione eseguita a motore
caldo, può causare fuoriuscite di
refrigerante o di vapori bollenti che
possono procurare gravi ustioni.
Rimuovere la semicarenatura destra
(Sez. E 2).
Svitare il tappo di carico (1) del
serbatoio di espansione.
Sistemare un recipiente sotto al
motore e porre il veicolo in appoggio
sul cavalletto laterale.
Svitare il tappo dal foro (2) di scarico
liquido posto sul coperchio pompa.
Lasciare defluire completamente
tutto il liquido.
Riavvitare nel foro (2) di scarico
liquido il tappo con nuova guarnizione.
Procedere al caricamento del circuito
versando liquido prescritto nuovo nel
vaso di espansione, dopo aver
rimosso il tappo (1).
Attendere qualche minuto per
consentire al liquido di riempire tutte
le canalizzazioni interne.
Riempire completamente il vaso di
espansione e richiudere il tappo (1).
Avviare il motore e portare la
temperatura del liquido a
110
°C
/
230
°F; far funzionare il motore per
circa
10
minuti.
Lasciare raffreddare il motore per
permettere la fuoriuscita dell’aria
presente nel circuito.
Attenzione
Non avvicinare mani, attrezzi e
indumenti alla ventola del radiatore
dell’acqua in quanto questa entra in
funzione automaticamente senza
preavviso e può procurare seri danni.
Importante
Verificare che non vi siano
perdite nel circuito.
Completare il caricamento dal
bocchettone del serbatoio di
espansione, portando il livello del
liquido alla tacca superiore
MAX
(3).
Serrare il tappo (1) del serbatoio di
espansione e rimontare le carenature
(Sez. E 2).
Changing the coolant
Warning
This operation must only be
carried out when the engine is cold.
Attempting to change the coolant with
the engine hot could lead to burns
from hot coolant or scalding steam.
Remove the RH side fairing
(Sect. E 2).
Remove the expansion tank filler
cap (1).
Place a container under the engine
and place the motorcycle on its side
stand.
Unscrew the plug from drain hole (2)
located on the pump cover.
Allow the coolant to drain off
completely.
Refit the cap to the drain hole (2)
along with a new gasket.
Fill the circuit by pouring new
recommended coolant into the
expansion tank after having removed
the cap (1).
Allow several minutes for the coolant
to fill all internal passages.
Completely fill the expansion tank and
replace the cap (1).
Start the engine and allow the coolant
to reach
110
°C
/
230
°F; run the
engine for around
10
minutes.
Let the engine cool to allow all air to
leave the cooling system.
Warning
Keep your hands, clothing and
tools well clear of the radiator fan at
all times; this fan starts automatically
without warning and could cause
serious injury or damage.
Important
Check the cooling circuit for
possible leaks.
Fill the circuit through the expansion
tank filler until the coolant level is
above the
MAX
upper mark (3).
Replace and tighten the cap (1) of the
expansion tank and replace the side
fairings (Sect. E 2).
1
MAX
MIN
3
2
Summary of Contents for 999R 2006
