Ducati 999R 2006, Repair Manual

Page: 61 / 606

Caratteristiche tecniche
Specifications
sezione / section
C 3
33
A
B
C
D
E
F
G
H
L
M
N
P
999R Aggiornamento/Update
- M.Y. 2006 - edizione/edition 00
Engine torque settings
Part Thread (mm) Nm Min. Max. Notes
Blow-by valve M 40x1.5 40 36 44
Pick-up filter cap M 32x1.5 42 38 46
Coolant intake manifold M 30x1.5 30 27 33 LOCK 6
Oil temperature sensor holder nut M 30x1.5 38 34 42 LOCK 4
Crankshaft gear nut M 25x1.5 190
*
171 209 GREASE B
Alternator rotor nut M 24x1 270 256 284 ENGINE OIL
Oil pick-up filter M 22x1.5 42 38 46
Coolant outlet union M 22x1.5 27 25 30 LOCK 5
Oil filler cap M 22x1.5 5
*
5 6
Primary drive gear nut M 22x1 190 171 209 GREASE B
Clutch centre nut M 20x1 190
*
180 200 GREASE B
Fixed/mobile tensioner pin M 20x1 50 45 55 LOCK 2 or THREE
BOND 1324
Crankshaft blanking plug M 20x1 Fully seated with tool THREE BOND 1375B
Cylinder head timing pulley nut M 17x1 71 64 78 GREASE A
Alternator cover inspection plug M 15x1 20 18 22 THREE BOND 1215
Selector drum locating screw M 16x1.5 30 27 33
Oil filter nipple M 16x1.5 42 38 46 LOCK 2 or THREE
BOND 1324
Oil filter cartridge M 16x1.5 11 10 12 Engine oil on gasket
Pick-up filter housing plug M 15x1 20 18 22 LOCK 5 or THREE
BOND 1375B
By-pass pump cap M 15x1 25 22 28 LOCK 5 or THREE
BOND 1375B
Timing belt driveshaft pulley nut M 15x1 71 64 78 GREASE A
Timing belt camshaft pulley nuts M 15x1 71 64 78 GREASE A
Low sump oil intake duct plug M 14x1.5 24 21 27 LOCK 5 or THREE
BOND 1375B
Radiator connection plug M 14x1.5 24 21 27 LOCK 5 or THREE
BOND 1375B
Oil cooler nipple M 14x1.5 27 24 30 LOCK 5 or THREE
BOND 1375B
Fixed tensioner bearing screw M 14x2 50 45 55 GREASE C
Timing belt driven gear nut M 14x1 55 * 50 60 GREASE A
Lower sump oil drain plug M 12x1.50 20 18 22
Oil temperature sensor M 12x1.5 18 * 16 19 LOCK 4
Coolant temperature sensor (control unit) M 12x1.5 23 20 26 LOCK 4
Pick-up sensor inspection screw M 12x1 15 13 17 LOCK 2 or THREE
BOND 1324
Earth connection bolt M 12x1 18 16 19 LOCK 2 or THREE
BOND 1375B
Head nuts: 1
st
step
2
nd
step
tightening
M 10x1.5 15
30
48
28
45 32
51
GREASE C