Index - 5
Internal information 2 .................................... 13-8
Interpolation axis ........................................... 9-19
Interpolation control....................................... 9-19
Interpolation speed designation method (
Pr.21
)
....................................................................... 5-35
Interrupt request during continuous operation
(
Cd.32
) ....................................................... 5-184
[J]
JOG (explanation of terms).............. Appendix-39
JOG operation ............................................... 11-4
JOG operation acceleration time selection
(
Pr.33
) ......................................................... 5-39
JOG operation deceleration time selection
(
Pr.34
) ......................................................... 5-39
JOG operation program ................................ 6-16
JOG operation start time chart.................... 11-11
JOG operation timing and processing times
....................................................................... 11-6
JOG speed (
Cd.19
) ................................... 5-183
JOG speed limit value (
Pr.32
).................... 5-38
JOG start signal............................................. 3-14
JUMP command............................................ 9-62
[K]
kPPS (explanation of terms) ............ Appendix-39
[L]
LED display function ..................................... 13-7
LIMIT SWITCH (explanation of terms)
.......................................................... Appendix-40
LINEAR INTERPOLATION (explanation of terms)
.......................................................... Appendix-40
LOW-INERTIA MOTOR (explanation of terms)
.......................................................... Appendix-40
Last executed positioning data No.(
Md.52
)
..................................................................... 5-158
List of condition data ................................... 5-131
List of configuration devices............................ 2-4
List of control data ....................................... 5-168
List of devices.................................................. 6-4
List of errors................................................... 14-6
List of functions................................................ 3-4
List of input/output signals ............................ 3-12
List of monitor data...................................... 5-136
List of parameters.......................................... 5-22
List of positioning data ................................ 5-112
List of start block data ................................. 5-127
List of warnings ............................................14-64
Load inertia ratio (
Md.106
) ..........................5-162
Load inertia ratio (
Pr.112
)
............................................. 5-63, 73, 83, 92, 109
Lower limit ......................................................3-18
Low pass filter/adaptive vibration suppression
control (
Pr.125
).............................................5-99
[M]
M CODE (explanation of terms) .......Appendix-40
M code OFF request....................................12-78
M code OFF request (
Cd.14
).....................5-174
M code ON signal ..........................................3-13
M code ON signal output timing (
Pr.19
).....5-32
M code ON/OFF timing................................12-78
M code output function ................................12-78
M code/condition data No. (
Da.9
)............5-124
MACHINE FEED VALUE (explanation of terms)
...........................................................Appendix-40
MANUAL PULSE GENERATOR
(explanation of terms) .......................Appendix-40
MASTER AXIS (explanation of terms)
...........................................................Appendix-41
MOVEMENT AMOUNT PER PULSE
(explanation of terms) .......................Appendix-41
MULTIPLYING RATE SETTING
(explanation of terms) .......................Appendix-41
Machine feed value........................................9-14
Machine feed value (
Md.30
) ......................5-146
Machine resonance suppression filter 1 (
Pr.118
)
........................................................................5-94
Machine zero point return................................8-4
Machine zero point return method ..................8-5
Main functions ..................................................3-6
Main positioning control ...................................9-2
Manual control ...............................................11-2
Manual pulse generator......................... A-16, 2-4
Manual pulse generator 1 pulse input
magnification (
Cd.23
).................................5-180
Manual pulse generator enable flag (
Cd.22
)
......................................................................5-180
Manual pulse generator operation ..............11-17
Manual pulse generator operation program
........................................................................6-16
Manual pulse generator operation start time chart
......................................................................11-24
Manual pulse generator operation timing and
processing times ..........................................11-19
Summary of Contents for A1SD75M1
