Mitsubishi A1SD75M1, User Manual

Page: 684 / 746

Appendix - 16
MELSEC-A
APPENDICES
(2) Servo parameters for MR-J-B
Item Setting range
Pr.100 Servo series 0: MR-H-B (MR-H-BN), 1: MR-J-B, 2: MR-J2-B, 1E: Other
Pr.101 Amplifier setting
0: Absolute position detection invalid
1: Absolute position detection valid
Regenerative
brake option
00: External regenerative brake option not used, 02: MR-RB013,
03: MR-RB033, 04: MR-RB064 2, 05: MR-RB32, 06: MR-RB34,
07: MR-RB54, 0F: MR-RB064
Pr.102
Regenerative
brake resistor
External dynamic
brake selection 0: External dynamic brake invalid
1: External dynamic brake valid
Pr.103 Motor type 0000
H
: HA-SH Standard, 0003
H
: HA-FH, 0005
H
: HA-MH
Pr.104 Motor capacity 0000
H
to 9999
H
Pr.105 Motor speed 1 to 3
Pr.106 Feedback pulse 0: 16384pulse, 1: 8192pulse
Pr.107 Rotation direction
0: Forward run with positioning address increment
1: Reverse run with positioning address increment
Pr.108 Auto tuning
0: Auto tuning selected for use of interpolation axis control in position
control, 1: Auto tuning for ordinary operation, 2: Invalid
Serv
o basic parameters
Pr.109 Servo response setting
1: Normal (low response), 2: Normal (low/middle response),
3: Normal (middle response), 4: Normal (middle/high response),
5: Normal (high response)
Pr.112 Load inertia ratio 0.0 to 100.0%
Pr.113 Position loop gain 1 4 to 1000rad/s
Pr.114 Speed loop gain 1 20 to 5000rad/s
Pr.115 Position loop gain 2 1 to 500rad/s
Pr.116 Speed loop gain 2 20 to 8000rad/s
Pr.117 Speed integral compensation 1 to 1000 ms
Pr.118 Notch filter selection 0: Not used, 1: 1125, 2: 563, 3: 375, 4: 282, 5: 225, 6: 1881, 7: 161
Pr.119 Feed forward gain 0 to 100%
Pr.120 In-position range 0 to 50000pulse
Pr.122 Monitor output mode selection
0: Servomotor speed, 1: Torque, 2: Servomotor speed (+),
3: Torque (+), 4: Current command, 5: Command speed,
6: Droop pulse 1/1, 7: Droop pulse 1/4, 8: Droop pulse 1/16,
9: Droop pulse 1/32
Carrier frequency
selection
0: 2.25KHz (Standard), 3: 9.0KHz (Low noise)
Pr.123
Option
function 1
Serial encoder
cable selection
0: 2-wire, 1: 4-wire (Supports long distance cables)
Serv
o adjustment parameters
Pr.124
Option
function 2 Motor-less
operation selection
0: Invalid, 1: Valid
Pr.127 Monitor output 1 offset –9999 to 9999mV
Pr.130 Zero speed 0 to 10000r/min
Pr.131 Error excessive alarm level 1 to 1000kpulse Serv
o
ex
tension
p
arameters
Pr.136 Speed differential compensation 0 to 1000