manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 881

Index

Power Blazer

871

TCP Connection Configuration .................. 365
TCP Connection Status .............................. 587
TCP Efficiency .................................... 566, 576
TCP Mode.................................................. 365
TCP Port ............................................ 304, 365
TCP Throughput .................. 81, 365, 576, 588
TCP Throughput Configuration ................. 366
TCP Throughput Threshold (% of ideal)..... 577
TC-RDI-P .................................................... 463
TC-RDI-V.................................................... 463
TC-REI-P..................................................... 464
TC-REI-V .................................................... 464
TC-TIM....................................................... 375
TC-TIM-P............................................ 463, 597
TC-TIM-V ........................................... 463, 597
TC-UNEQ-P ........................................ 346, 462
TC-UNEQ-V........................................ 346, 462
TC-VIOL-P .................................................. 463
TC-VIOL-V.................................................. 463
TDEV ......................................................... 478
TE (ns) ....................................................... 592
TE Scale ..................................................... 594
technical specifications.......................... 2, 759
technical support ...................................... 752
Temp. Threshold........................................ 367
Temperature.............................................. 562
temperature for storage............................ 747
TERM......................................................... 169
Termination............................................... 169
Test ................................................... 312, 515
Test Applications ......................................... 47
Test Block .................................................. 118
Test Configurator ...................................... 107

Ethernet Test Applications ................... 114
Fibre Channel Test Application ............ 115
Intelligent Apps ................................... 112
Overview.............................................. 112
Packet Sync Test Applications .............. 115
Transport Test Applications ................. 114
Wireless Test Applications.................... 115

Test Control................................................. 38
Test Equipment ......................................... 363

Test Function ............................................. 312
Test ID ....................................................... 315
Test Menu.................................................... 38
Test Parameters ......................................... 324
Test Pattern ............................................... 315
Test Recovery.... 532, 540, 554, 557, 559, 567, 

569, 572, 575, 578, 583, 586, 589,
591

Test Sequence block .................................. 112
Test Setup.................................................... 47
Test Status

.... 531, 540, 545, 554, 565, 567, 

578, 583, 586, 589, 591

Test Timer.................................................... 38
tHEC .......................................................... 658
tHEC-CORR ................................................ 421
tHEC-UNCORR............................................ 422
Threshold........................................... 366, 491
Threshold (% of ideal)........................ 270, 305
Thresholds ................. 224, 308, 528, 529, 530
Through..................................................... 129
Through Intrusive ...................................... 130
Through Mode............................................. 80
Throughput ....... 182, 261, 294, 359, 539, 573

Streams................................................ 530

Throughput button ................................... 487
Throughput meter ..................................... 587
Throughput Pass/Fail Verdict ..................... 366
Throughput Threshold............................... 587
TIE (ns)....................................................... 593
TIE Scale .................................................... 594
TIM ............................ 431, 433, 435, 442, 447
Time .................................................. 494, 640
Time Error.................................................. 479
Time Interval Error ..................................... 479
Time Mode ........................................ 493, 520
Time Source....................................... 152, 543
Time Stamp ....................................... 491, 520
Time Zone.................................................. 363
Timeout ............................................. 687, 688
Timer ........................................... 38, 107, 368
Timeslot..................................................... 346
TIM-P ......................................... 375, 459, 597

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands