EXFO Power Blazer 88200NGE User Manual Download Page 332

Page: 332 / 887

Test Setup - Test Configurator, Timer, and System

322

88000 Series

Services - Profile

Note:

The

CIR

value will be calculated on the basis of the selected service profile

and the value entered in the

Number of Calls

Number of Channels

field.



Frame Size (Bytes)

indicates the frame size for

Voice

and

Video

profiles and allows changing the frame size for

Data

profile:



Fixed

(default)

Profile and

Codec

Type

Frame Size (bytes)

IPv4

IPv6

Voice Codec:
- VoIP G.711
- VoIP G.723.1
- VoIP G.729

Fixed

138
82
78

158
102
98

Video Codec: All

Fixed

1374

1394

Data

Fixed

(default)

(default) to 16000

The minimum value is adjusted according to the frame structure and

components selected as shown in the following table.

The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical

interface.

Random

to 1518

The maximum frame size value is adjusted for each enabled VLAN (+4 bytes

per VLAN).

EMIX

to 16000

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands