manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 375

Test Setup - Test Configurator, Timer, and System

Power Blazer

365

TCP Throughput

TCP Throughput 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, and tap on the test 

block. 

TCP Mode

Since two units are required to perform a TCP Throughput test, one unit 
must be the source (

Local

) unit and the other one the destination 

(

Remote

). Set the TCP Mode on both units: 

Local 

(default) or 

Remote

. 

TCP Connection Configuration

Remote IP Address

, available with 

Local

 TCP mode, allows entering 

the IP address of the remote unit. 

Quick Ping

 button automatically starts the quick Ping utility for the 

remote IP address and provides either a successful or failed result. The 
quick Ping uses 3 attempts, a Delay of 1 second, a Timeout of 2 
seconds, and a Data Size of 32 Bytes. Refer to 

Ping & Trace Route

 on 

page 686 for more options. 

Accept Connection from IP

, available with 

Remote

 TCP mode, allows 

entering the IP address of the local unit. The IP address 

0.0.0.0

 

(default) listens to any TCP stream. 

IP TOS/DS

, available with 

Local

 TCP mode, is configurable from 

0x00

(default) to 

0xFF

. 

TCP Port

, available with 

Local

 and 

Remote

 TCP modes, allows the 

selection of the TCP port number: 

0

 to 

65535

 (default is 

50201

). For the 

local unit, the specified TCP port will be used for the TCP initialization 
algorithm with the remote unit. The following TCP segments sent by 
the local unit will use the TCP port number replied by the remote unit. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands