manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 371

Test Setup - Test Configurator, Timer, and System

Power Blazer

361

SyncE

SyncE 

From the 

Test

 menu, tap

 Setup

, 

Test Configurator

, and the 

SyncE

 test 

block. 

ESMC Monitoring 

ESMC

 (Ethernet Synchronization Message Channel) is a live value 

monitored even when the test is not started. 

An arrow next to the ESMC label indicates that ESMC valid information 
frames are received or not.

A green arrow indicates that at least one ESMC valid information 
frame, containing a valid FCS, was received within a second in the 
last 5-second interval.

A red arrow indicates that no ESMC valid information frames were 
received for more than 5 seconds.

A gray arrow indicates awaiting incoming data to provide a status.

Received QL 

indicates the last Quality Level received. The 

Received QL

 is a live value monitored even when the test is not 

started. 

QL Mismatch Monitoring

 check box when selected (default) enables 

the Quality Level mismatch monitoring. The quality level characterizes 
the clock quality in terms of network synchronization. 

Expected QL

 available when the 

QL Mismatch Monitoring

 check box 

is selected, allows the selection of the Expected Quality Level value. 
See page 512 for more information. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands