manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 510

Test Results

500

88000 Series

OTL-SDT

Longest Disruption

 indicates the longest measured disruption time. 

Lanes with Disruption

 indicates the number of lanes with service 

disruption. 

Note:

When a disruption event is equal to or longer than the test period which is 
fixed to 5 minutes, then the measured disruption time is equal to the test 
period.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands