EXFO Power Blazer 88200NGE User Manual Download Page 730

Page: 730 / 887

Test Control

720

88000 Series

Discover Remote Button



Loop Up

and

Loop Down

buttons (Not available with RFC 6349 test

application)



Loop Up

establishes the connection with the selected remote unit

and sets the remote unit into

Smart Loopback

test application.

If a remote unit is in any busy status, a user confirmation is
required to proceed with the Loop Up command.

Following a successful loop up, the IP address of the remote unit
will be used as the destination IP address for the test.

Once the connection is established with the remote unit, the local
unit can be set for EtherSAM, RFC 2544, EtherBERT, or
Traffic Gen & Mon testing.



Loop Down

ends the connection between the local and the

remote units.



Connect

and

Disconnect

buttons are only available with RFC 2544,

RFC 6349, and EtherSAM test applications.



Connect

establishes the connection with the selected remote unit

and sets the remote unit into either DTS RFC 2544, DTS RFC 6349,
or DTS EtherSAM test application, depending on the active test on
the local unit.

If a remote unit is in any busy status, a user confirmation is
required to proceed with the Loop Up command.

Following a successful connection, the IP address of the remote
unit will be used as the destination IP address for the test.



Disconnect

ends the connection between the local and the

remote units.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands