manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 661

Test Functions

Power Blazer

651

GMP

GMP 

Note:

Available with Transport test applications with either payload type 21 
(PT21) or one of the following clients: 

1GbE

, 

40GbE

, 

100GbE

, 

Ethernet 

(flex/GFP-F)

, or SONET/SDH (through ODU0). 

From the

 Test

 menu, tap 

Functions

, and the 

GMP

 tab. 

Channel

 available with Multi-Channel OTN allows the selection of the 

channel number. 

Generic Mapping Procedure 

TX Cm

 indicates the minimum and maximum Cm value transmitted 

during the test. 

TX CnD

 indicates the minimum and maximum CnD value transmitted 

during the test. 

RX Cm

 indicates the minimum and maximum Cm value captured 

during the test. 

RX CnD

 indicates the minimum and maximum CnD value captured 

during the test. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands