manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 832

Glossary

822

88000 Series

Generic Framing Procedure (GFP) 

GFP Summary

GFP has been standardized to better optimize the transport of Ethernet and 
other data services over SONET, taking into account both the pros and cons 
of ATM and PPP/HDLC framing mechanisms. As described in this section, 
GFP represents a robust mapping mechanism that allows for the mapping 
of multiple client-data types into SONET/SDH payload (SPEs). This 
technology has been embraced by network equipment and service 
providers as it provides an efficient way of providing interoperable 
data-services transport over the existing SONET/SDH install base. The 
versatility provided by GFP allows SONET/SDH networks to offer transport 
services for a multiple of services, as shown in figure below.

Multiservice SONET/SDH Network

 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands