manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 681

Test Functions

Power Blazer

671

OH - SONET/SDH

For OC-12: The M1 byte located in the STS-1 #7 indicates BIP 
violations.

For OC-48: The M1 byte located in the STS-1 #7 indicates BIP 
violations.

For OC-192: Either the M1 byte located in the STS-1 #7, or the 
combination of the M0 and M1 bytes indicates BIP violations (refer 
to 

REI-L Computation Method 

on page 346).

For 

M1 Only

 computation method:

M1, bits 234 5678

Indicates

000 0000

0 BIP violation

000 0001

1 BIP violation

:

:

110 0000

96 BIP violations

110 0001 to 

1111 1111

0 BIP violation

M1

Indicates

0000 0000

0 BIP violation

0000 0001

1 BIP violation

:

:

1111 1111

255 BIP violations

M1

Indicates

0000 0000

0 BIP violation

0000 0001

1 BIP violation

:

:

1111 1111

255 BIP violations

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands