manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 570

Test Results

560

88000 Series

Summary (FlexO BERT)

BER 

Note:

See 

BER

 on page 396 for a description of each alarm/error. 

Receiving Live Traffic - RX Pattern Analysis Disabled 

when 

displayed, indicates that the 

No Pattern Analysis (Live)

 check box is 

selected and in this case no other information/statistics are available. 

BER Threshold

 is available when 

Pass/Fail Verdict

 is enabled

1

. This 

setting is global and applies to all Client ID. 

Bit/Pattern Error Rate/Count

 graphically displays a meter 

representing either the bit/pattern error rate or the bit/pattern error 
count depending on the Pass/Fail Verdict selection

1

. 

When the verdict is enabled

1

, the values under the threshold are 

presented in green while the values above are in red. 

When the verdict is disabled, the bit/pattern error rate is displayed in 
blue. 

The arrow pointer indicates the current received bit/pattern error 
rate/count. 

The Pass/Fail verdict is displayed just on top of the meter when 
enabled

1

. 

Bit/Pattern Error

, 

Amount/Rate

, and 

Inject

: The bit/pattern error 

injection and settings are coupled with the 

Inject Button

 on page 473. 

1. Refer to 

BERT and Unframed BERT

 on page 155. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands