EXFO Power Blazer 88200NGE User Manual Download Page 411

Page: 411 / 887

Test Results

Power Blazer

401

Alarms/Errors Overview

Note:

For Wander test application only

AIS

and

LOF

alarms are supported.

Alarms

Note:

Only AIS is available when the framing is set to

Unframed



AIS

(Alarm Indication Signal)

: Two or less ZEROs are received in each of two consecutive double

frame periods (512 bits).



LOF

(Loss Of Frame)

: Three consecutive incorrect frame alignment signals is received.



RAI

(Yellow) (Remote Alarm Indication)

: Bit 3 in timeslot 0 is set to “1”.



TS16 AIS

(TimeSlot 16 Alarm Indication Signal)

: Three or less ZEROs are received in each Timeslot 16 of two

consecutive multiframes.



LOMF

(Loss Of MultiFrame)

: Two consecutive multiframes alignment signals (bits 1 through 4 of

TS16 of frame 0) is received with an error.



RAI MF

(Remote Alarm Indication Multi-Frame)

: Bit 6 of timeslot 16 of frame 0 is set to “1”.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands