Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 566 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 566

Test Results

556

88000 Series

Summary (FC BERT)

Round-Trip Latency



Round Trip Latency (ms)

is measured for each local and remote port.

Current

,

Average

,

Minimum

, and

Maximum

indicates respectively the

current, average, minimum, and the maximum round trip latency from
the local to the remote port in the last one second. The pass/fail verdict
is also displayed for the maximum round trip latency.

Samples

indicates the number of samples used for the round trip

latency.



Estimated BB_Credit

indicates the estimated number of packets that

can be transmitted on the optical line at the same time.



Round-Trip Latency Threshold (ms)

sets the round trip latency

threshold:

0.015

to

8000 ms

(default is

15

). This setting is only

available when both

Latency Tags

and

Pass/Fail Verdict

check boxes

are selected (refer to

Latency Tag Insertion

Traffic



Line Utilization (%)

indicates the current percentage of the

transmitting/receiving line rate utilization.



Frame Rate (frame/s)

indicates the current transmitted/received

number of frames (including frame with error and aborted frames) in
frame per second.



Byte Count

indicates the total number of transmitted/received bytes

including the frame delimiters.



Frame Count

indicates the total number of transmitted/received

frames including link service control frames.

«
...
564
565
566
567
568
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands