Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 149 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 149

Test Setup - Test Configurator, Timer, and System

Power Blazer

139

Modify Structure Button



16 Unframed 400GAUI-16

: Independent infinite length test pattern

in each 400GAUI-16 lane (no blocks). Available with
CFP8 - 400GE (8 Lanes).



Loopback Mode

Note:

Only available for Smart Loopback Ethernet test application.

Transparent (Pseudo-Physical

) check box when selected (cleared by

default) determines that the Smart Loopback operates as a physical
loopback by transmitting all received frames unaltered and without
discrimination. When the check box is cleared, the Loopback mode is
selectable from

In transparent mode, the

Network

tab and the

Ping & Trace Route

functions are not available.

Note:

The

Transparent

mode is intended to be used for point-to-point topology,

not for switched or routed networks. Use the

Transparent

mode with

caution because all received frames are looped back without
discrimination.

«
...
147
148
149
150
151
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands