manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 134

Test Setup - Test Configurator, Timer, and System

124

88000 Series

Modify Structure Button

Note:

For Multi-Channel OTN, ODU0 mapping is selected by default and the 

OTN Multiplexing

 field is not displayed. Refer to Modify Trib 

Slots/Channels

 on page 282

 for test mapping selection and Multi-Channel 

OTN

 on page 51

 for supported path/mapping. 

Interface/Rate

OTN Multiplexing

OTU1 [2.666 Gbit/s] ODU1 

ODU1/ODU0 

OTU2 [10.709 Gbit/s] ODU2 

ODU2/ODU1 
ODU2/ODU1/ODU0
ODU2/ODU0 
ODU2/ODUflex 

OTU1e [11.049 Gbit/s] ODU1e
OTU2e [11.096 Gbit/s] ODU2e
OTU1f [11.270 Gbit/s] ODU1f
OTU2f [11.318 Gbit/s] ODU2f
OTU3 (4 Lanes) [43.018 Gbit/s]

ODU3

 

ODU3/ODU2
ODU3/ODU2/ODU1
ODU3/ODU2/ODU1/ODU0
ODU3/ODU1
ODU3/ODU1/ODU0
ODU3/ODU0
ODU3/ODUflex 

OTU3e1 (4 Lanes) [44.571 Gbit/s]

ODU3e1

OTU3e2 (4 Lanes) [44.583 Gbit/s]

ODU3e2

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands