manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 383

Test Setup - Test Configurator, Timer, and System

Power Blazer

373

Traces (OTN)

SAPI OTU/ODU/TCM-TIM

 check box, when selected (cleared by 

default), allows editing the expected Source Access Point Identifier 
(SAPI) and also enables OTU/ODU/TCM-TIM alarm monitoring. 

DAPI OTU/ODU/TCM-TIM

 check box, when selected (cleared by 

default), allows editing the expected Destination Access Point Identifier 
(SAPI) and also enables the OTU/ODU/TCM-TIM alarm monitoring. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands