Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 714 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 714

Test Functions

704

88000 Series

RTD/RTT (CPRI/OBSAI Framed L2)

RTD/RTT (CPRI/OBSAI Framed L2)

Note:

Only available with CPRI/OBSAI Framed L2 in

Base Station

emulation

mode.

Round Trip Delay (RTD for CPRI) and Round Trip Time (RTT for OBSAI)
measurements are needed to quantify the time it takes for a signal to cross
the remote radio head and come back.

Note:

Be aware that RTD/RTT requires error free operation conditions to provide
reliable results. Therefore, RTD/RTT results could be affected by error
injection or error introduced by the network.

From the

Test

menu, tap

Functions

, and the

RTD/RTT

tab.

Note:

For

Dual Port

topology select the port to be displayed.

RTD

RTT

«
...
712
713
714
715
716
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands