manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 533

Test Results

Power Blazer

523

Service Configuration - L2CP

The L2CP frame verdict is as follows per direction: 

L2CP service verdict is as follows per direction: 

L2CP global verdict is as follows: 

Verdict

Description

PASS

If the Expected L2CP Handling is 

Pass Through

 and the L2CP TX frames have 

been received at destination with a maximum of 1 frame lost.

If the Expected L2CP Handling is 

Peer/Discard

 and none of the transmitted 

L2CP frames have been received at destination.

FAIL

If the Expected L2CP Handling is 

Pass Through

 and none or some but not all 

(more than 1 frame lost) of the transmitted L2CP frames have been received 
at destination.

If the Expected L2CP Handling is 

Peer/Discard

 and at least one of the 

transmitted L2CP frames have been received at destination.

Verdict

Description

PASS

All L2CP frame verdicts (same direction) are pass.

FAIL

At least one L2CP verdict (same direction) is fail.

Verdict

Description

PASS

All L2CP service verdicts are pass.

FAIL

At least one L2CP service verdict is fail.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands