EXFO Power Blazer 88200NGE User Manual Download Page 303

Page: 303 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

293

RFC 2544 - Global



Frame Size (Bytes):

For

RFC 2544

distribution, gives predefined frame

size distribution values. For

User Defined

distribution, enter up to

seven frame size values.

The following table lists each component that may affect the minimum
size value.

Restore RFC 2544 Defaults

Reverts the configured parameters to their default values.

Distribution

Frame Size

RFC 2544

128

256

512

1024

1280

, and

1518

The minimum frame size will be adjusted according to the frame structure and

components selected.

User Defined

16000

The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical

interface.

Component

Description

VLAN

4 bytes per VLAN tag (up to 3 VLAN tags)

LLC and SNAP Headers

8 bytes

IPv4

20 bytes

IPv6 40

bytes

Using DTS

4 bytes

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands