manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 275

Test Setup - Test Configurator, Timer, and System

Power Blazer

265

Network

Subnet Mask

1

: Enter the Subnet Mask. The default setting is 

255.255.000.000

. 

Default Gateway

1

 check box, when selected (cleared by default), 

allows entering a default Gateway IP address. When the 

Default 

Gateway

 check box is selected, its default address is 

0.0.0.0

. 

For 

IPv6

 the following configuration parameters are displayed: 

Link-Local 

IPv6 Address

, 

Global IPv6 Address

, and 

Default Gateway

. Tap on the 

Config

 button to access all settings. 

Link-Local IPv6 Address

 (LLA) is used for local communication 

between on-link neighbors and for Neighbor Discovery process. 

Mode

Stateless Auto

 (default) allows automatic generation of the IPv6 

address based on the MAC address. 

Static

 allows entering the IP Address. 

Address

, available with 

Static

 mode, allows selecting the 

Link-Local IPv6 Address. The accepted range is from 

FE80:0000:0000:0000:0000:0000:0000:0000

 to 

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF.

 The default address 

is

 FE80::[Interface ID]

, where [

Interface ID

] is generated from 

the source MAC address. When the 

Address

 field is selected for 

editing using virtual keyboard, the 

Previous IPs

 button appears 

allowing the selection of a previously configured IP address. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands