Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 328 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 328

Test Setup - Test Configurator, Timer, and System

318

88000 Series

Services - Global

Total TX Rate

Note:

Only available when the

Service Performance Test

check box is selected

(see

EtherSAM - Global

on page 193). For

Dual Test Set

, the total TX rates

are displayed for both

Local

and

Remote

directions.



Committed

displays the total enabled TX rate (bandwidth) that will be

generated by the selected service(s).



Available

displays the total TX rate (bandwidth) available for traffic

generation.

Global Options

Rate Unit

choices are

%

(default),

Mbit/s

, and

Gbit/s

.

Copy Service Button

Copy Service

button allows copying the services configuration to one or

several services.



Copy Service

allow selecting the services number from which the

configuration will be copied from.



To the following Services

allows selecting all services that will inherit

the configuration from the selected service. An orange background
represents a selected service. A service that is already enabled cannot
be selected for copy.



Copy

allows confirming the service configuration copy for all selected

services.

«
...
326
327
328
329
330
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands