manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 359

Test Setup - Test Configurator, Timer, and System

Power Blazer

349

Smart Loopback

Smart Loopback 

Note:

The Smart Loopback block is only displayed when the 

Transparent 

(Pseudo-Physical

) check box is cleared (see 

Loopback Mode

 on 

page 139).

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, and the Smart 

Loopback block. 

Loopback 

Mode

 determines at which layer the Smart Loopback address/port 

swapping operation will be. 

Ethernet

 swaps the MAC addresses of received packets having 

their 

Destination MAC

 address matching the MAC address of the 

loopback port. 

Ethernet (All Unicast)

 swaps the MAC addresses of received 

packets having Unicast 

Destination MAC

 address. 

IP

, for Ethernet Layer 3 and 4, swaps the MAC and IP addresses of 

received packets having their 

Destination IP

 address matching the 

IP address of the loopback port. For Ethernet Layer 2, swaps the 

MAC addresses

 for packets having their 

Destination MAC

 address 

matching the MAC address of the loopback port. 

UDP/TCP

 (default), for Ethernet Layer 4, swaps the UDP or TCP 

ports and the MAC and IP addresses of received packets having 
their 

Destination IP

 address matching the IP address of the 

loopback port. For Ethernet Layer 3, swaps the MAC and IP 
addresses for packets having their 

Destination IP

 address 

matching the IP address of the loopback port. For Ethernet Layer 2, 
swaps the 

MAC addresses

 for packets having their 

Destination 

MAC

 address matching the MAC address of the loopback port. 

Matching & Swapping

 indicates the Loopback parameters that will be 

used based on the Loopback Mode selected. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands