EXFO Power Blazer 88200NGE User Manual Download Page 301

Page: 301 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

291

RFC 2544 - Global

RFC 2544 - Global

From the

Test

menu, tap

Setup

Test Configurator

, tap on the RFC 2544

block, and on the

Global

tab.

Dual Test Set



Dual Test Set

(

DTS

) check box when selected (cleared by default)

enables RFC 2544

Dual Test Set

. Once

Dual Test Set

is enabled, use

the

Discover Remote

button to select a remote unit. Not available in

Dual Port

topology.

Note:

It is also possible using the Discover Remote button to connect to a remote

module and automatically enable

Dual Test Set

. For more details, refer to

Discover Remote Button

on page 718.



Disconnected

indicates that there is no connection established

with a remote module.



Connected

indicates that the connection is established with a

remote module.



Discover Remote

button allows discovering remote module

supporting

Remote Loopback

and/or

Dual Test Set

. For more details,

refer to

Discover Remote Button

on page 718.

Global Options



Flow Direction

allows the selection of the traffic direction as follows:



TX to RX

for

Single Port

topology.



Port #1 to Port P2

Port #2 to Port #1

, and

Bidirectional

for

Dual Port

topology.



Local to Remote

Remote to Local

, and

Bidirectional

for

Dual

Test Set

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands