Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 245 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 245

Test Setup - Test Configurator, Timer, and System

Power Blazer

235

Interface



Modify Wavelength

button, available with tunable transceivers when

the

TunableOptics

software option is enabled, is used to configure the

transceiver wavelength.



Wavelength

(nm) indicates the actual wavelength value selected.

Use the scroll box and/or the -/+ buttons to select the wavelength.
The minimum and maximum wavelength values are displayed.



Channel Number

indicates the actual ITU channel number based

on ITU Grid.



Frequency

(THz) indicates the actual Frequency based on ITU Grid



Channel Spacing

(GHz) indicates the difference in frequency

between two adjacent channel detected from the transceiver
device.



Restore Previous

restores the current value present in the

transceiver device.



Power Range (dBm

) indicates the transceiver operational RX power

range.

FEC (FlexO BERT)

FEC

check box when selected (default) enables the FEC in TX/RX and

allows detecting, reporting, and correcting up to 15symbol errors
(Correctable) per codeword. If there are over 15 symbol errors
detected, they are reported as uncorrectable errors.

«
...
243
244
245
246
247
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands