EXFO Power Blazer 88200NGE User Manual Download Page 139

Page: 139 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

129

Modify Structure Button



Topology

allows the selection of the network test topology. Only

Coupled (TX=RX)

is available with Multi-Channel OTN and FlexO

BERT.



Coupled (TX=RX)

uses the same settings for both the TX and RX

signals.



Decoupled (TX

≠

RX)

, supported with

SONET/SDH BERT

8870/8880/88260 module,

DSn/PDH BERT

, and

SONET/SDH -

DSn/PDH

test applications, uses independent settings for TX and

RX signals. However, the pattern and some other parameters are
always coupled.



Through

loops the RX signal to the TX port without TX overwrite

capabilities.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands