EXFO Power Blazer 88200NGE User Manual Download Page 774

Page: 774 / 887

Glossary

764

88000 Series

Acronym List

DS0

Digital Signal-level 0 (64 Kbit/s)

DS1

Digital Signal-level 1 (1.544 Mbit/s)

DS3 Digital

Signal-level 3 (44.736 Mbit/s)

DSn

Digital Signal-level n

DSP Digital

signal processor

DST

Destination

DTE

Data Terminal Equipment

dTE

dynamic Time Error High

DUS

Don’t Use for Synchronization

DUT

Device Under Test

E-VLAN

Extended Virtual Local Area Network

European standard for digital transmission-level 0 (64 Kbit/s).

European standard for digital transmission-level 1 (2.048 Mbit/s).

European standard for digital transmission-level 2 (8.448 Mbit/s).

European standard for digital transmission-level 3 (34.368 Mbit/s).

European standard for digital transmission-level 4 (139.264 Mbit/s).

Errored Block

EBS

Excess Burst Size

Error Count

ECN

Explicit Congestion Notification

ECT

ECN Capable Transport

EEC

Ethernet Equipment Clock

EFS

Error Free Second

eHEC

extension Header Error Check

EIR Excess

Information

Rate

EoE Ethernet

over

Ethernet

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands