EXFO Power Blazer 88200NGE User Manual Download Page 67

Page: 67 / 887

Test Setup - Test Applications

Power Blazer

OTN-SONET/SDH BERT



Path/Mapping

The

OTN-SONET/SDH BERT

test application offers the following

path/mapping structures depending on the module, inserted
transceiver, and enabled options.

For OTN-SONET BERT: up to OTU4 for 88200NGE, up to OTU3 for 88260,
and up to OTU2 for 8870/8880.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands