EXFO Power Blazer 88200NGE User Manual Download Page 535

Page: 535 / 887

Test Results

Power Blazer

525

Service Configuration - Ramp



Informational

parameters are for information purpose only, they are

not included in the test pass/fail verdict. See

Summary (EtherSAM)

page 551 for more information on

Frame Loss

Max Jitter

, and

Round-Trip Latency



Average RX Rate

indicates the measured average utilization

throughput for each step.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands