manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 209

Test Setup - Test Configurator, Timer, and System

Power Blazer

199

EtherSAM - L2CP

Destination MAC Address

: For predefined L2CP frames allows 

selecting the 

Destination MAC Address

 for frames having more than 

one allowed MAC Addresses. For user defined allows selecting the 

Destination MAC Address

 from 

01-80-C2-00-00-00

 (default) to 

01-80-C2-FF-FF-FF

 for 

User (01-80-C2)

 and from 

01-00-0C-00-00-00

 

(default) to 

01-00-0C-FF-FF-FF

 for 

User (01-00-0C)

. 

LLC

 (available with LLC and SNAP frame formats) 

SSAP

: 

0x00

 to 

0xFF

 (

0x42

 by default) for LLC frame format; fixed 

to 

0xAA

 for SNAP frame format.

DSAP

: 

0x00

 to 

0xFF

 (

0x42

 by default) for LLC frame format; fixed 

to 

0xAA

 for SNAP frame format. 

Control

: 

0x00

 to 

0xFF

 (

0x03

 by default) for LLC frame format; 

fixed to 

0x03

 for SNAP frame format. 

Note:

For LLC frame format, the following concatenated values of 
DSAP/SSAP/Control are not valid since they are reserved for SNAP frame 
format: 0xAAAA03 or 0xABAB03. 

OUI 

(available with SNAP frame format): 

0x000000

 (default) to 

0xFFFFFF

. 

EtherType

 (available with SNAP and Ethernet II frame formats): 

0x0000

 to 

0xFFFF

 for SNAP and 

0x0600

 to 

0xFFFF

 (excluding 0x8100, 

0x88A8, 0x9100, 0x9200, 0x9300, 0x8847, and 0x8848) for Ethernet II. 
Default is 

0x0600

. 

Subtype

, only available for some predefined L2CP frames, indicates 

the subtype for the frame. 

Custom Bytes

 (16 bytes) 

0x00000000000000000000000000000000

 

(default) to 

0xFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

. Only available 

for user defined L2CP frames. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands