EXFO Power Blazer 88200NGE User Manual Download Page 736

Page: 736 / 887

Test Control

726

88000 Series

Lpbk Tool Button (Loopback Tool)



Loopback Mode

determines at which layer the address/port swapping

is limited.



Ethernet

swaps the MAC addresses of received packets having

their

Destination MAC

address matching the MAC address of the

loopback port.



Ethernet (All Unicast)

swaps the MAC addresses of received

packets having Unicast

Destination MAC

address.



, for Ethernet Layer 3 and 4, swaps the MAC and IP addresses of

received packets having their

Destination IP

address matching the

IP address of the loopback port. For Ethernet Layer 2, swaps the

MAC addresses

for packets having their

Destination MAC

address

matching the MAC address of the loopback port.



UDP/TCP

(default), for Ethernet Layer 4, swaps the UDP or TCP

ports and the MAC and IP addresses of received packets having
their

Destination IP

address matching the IP address of the

loopback port. For Ethernet Layer 3, swaps the MAC and IP
addresses for packets having their

Destination IP

address

matching the IP address of the loopback port. For Ethernet Layer 2,
swaps the

MAC addresses

for packets having their

Destination

MAC

address matching the MAC address of the loopback port.



Traffic



Line Utilization (%)

indicates the current percentage of the

transmitting/receiving line rate utilization.



Ethernet BW (Mbit/s)

indicates the current transmitting/receiving

data rate expressed in Mbit/s.



Frame Rate (frame/s)

indicates the current transmitted/received

number of frames (including bad frames, Broadcast frames and
Multicast frames) in frame per second.



Frame Count

indicates the total number of transmitted/received

valid and invalid frames.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands