manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 281

Test Setup - Test Configurator, Timer, and System

Power Blazer

271

Network Details (iSAM)

Services 

Allows the selection of the number of services: 

1

 (default) to

4

. 

The following parameters are configurable individually for each service: 

Profile

 

Two profiles are defined by default as well as 

User Profile

. Profiles are 

user definable and up to 25 profiles can be predefined (see 

Customizable Profiles

 on page 276). 

Profile

Parameter

Frame Type

Frame Sizes

VLAN Priority DSCP Performance Criteria

Priority

EMIX

64

, 

128

, 

512

, 

1024

, 

and 

1518

a

a.

The minimum frame size value is adjusted according to the frame structure and components selected as

shown in the table of 

Frame Size

 on page 273. 

7

CS7

b

b.

ECN is not present and not configurable but is set to 00 (Not-ECT). 

MEF Metro High

Best Effort

0

CS0

b

MEF Metro Low

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands