manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 353

Test Setup - Test Configurator, Timer, and System

Power Blazer

343

Signal - Signal Configuration (OTN)

Modify Tributary Slots/Port

1

 

The payload type 20 or 21 is indicated for each mapped OPU level. 

Fixed Structure

 check box when selected (default) for OPU3, the 

selection of a tributary slot will automatically select four tributary 
slots from the same column, which constitute the foreground 
traffic. When the 

Fixed Structure

 check box is cleared, select the 

four tributary slots individually. 

1. Not available with Multi-Channel OTN. 

For...

Mapped into...

Tributary slot selection

ODU3

OPU4

31

ODU2e
ODU1e

OPU4

8

ODU2

OPU4
OPU3

8 
4 (PT20), 8 (PT21)

ODU1

OPU4
OPU3
OPU2

2 
1 (PT20), 2 (PT21) 
1 (PT20), 2 (PT21) 

ODU0

OPU4
OPU3
OPU2
OPU1

1 
1 
1 
1 

ODUflex

OPU4
OPU3 
OPU2 

up to 80 
up to 32 
up to 8 

ODUflex/GFP-F

OPU4
OPU3
OPU2 

up to 8 
up to 8 
up to 8 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands