manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 770

Specifications

760

88000 Series

General Specifications 

Transceiver System 

Specification

8870/8880/ 

88200NGE

88260 

88400NGE 

88460 

Temperature 

Operating: 0 °C to 40 °C (32 °F to 104 °F)
Storing: -40 °C to 70 °C (-40 °F to 158 °F)

Relative humidity

0 % to 95 %, non-condensing 

Maximum 
operation altitude

5000 m (16000 ft) 

Pollution degree

3 

Measurement 
category

Not rated for measurement categories II, III, or IV 

Specification

TA-QSFP28

TA4-CFP8 

TA4-QSFP-DD 

Temperature 

Operating: 0 °C to 40 °C (32 °F to 104 °F) 
Storing: -40 °C to 70 °C (-40 °F to 158 °F) 

Relative humidity

0 % to 95 %, non-condensing 

Maximum operation altitude 5000 m (16000 ft) 
Pollution degree

3 

Measurement category

Not rated for measurement categories II, III, or IV 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands