EXFO Power Blazer 88200NGE User Manual Download Page 145

Page: 145 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

135

Modify Structure Button



Unframed (Interop)

is only available with optical interface up

to 25GE:

For

Seed A

and

Seed B

, available with 10G LAN and 25G, the

pattern is generated by the PCS scrambler from a specific seed.
The pattern is not encoded.

For

PRBS31 Unscrambled

, available with 10G LAN and 25G, the

pattern is generated at the PCS layer. The pattern is not encoded
and not scrambled.

For

PRBS

and

User Pattern

: Pattern generated by the PCS

scrambler. The pattern is encoded.



Unframed

is only available with optical interface up to 10G LAN:

Encoded pattern generated by the PCS scrambler.



Unframed with Sync

is only available with optical interface up to

10G LAN: Pattern of a length corresponding to the number of bytes
transmitted in 1 second.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands