EXFO Power Blazer 88200NGE User Manual Download Page 448

Page: 448 / 887

Test Results

438

88000 Series

Alarms/Errors Overview



OOMFI

(Out of OPU Multi-Frame Identifier) is only available for OPU4

of a mapped signal.

: OPU Multi-frame Identifier number are in error for at least

5 consecutive OTU frames.



PLM

(Payload Mismatch) is available when OPU-PLM check box is

selected.

: The Payload Structure Identifier (PSI) field does not match the

expected PT for at least 3 consecutive frames.



MSIM Monitoring

check box when selected (default) monitors the

MSIM

alarm.

Errors



OMFI

(OPU Multi-Frame Identifier) is only available for OPU4 of a

mapped signal.

: Invalid OMFI word sequence detected.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

EXFO Power Blazer 88200NGE, User Manual, Page: 448 / 887

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews: