manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 251

Test Setup - Test Configurator, Timer, and System

Power Blazer

241

Link OAM

OAM Discovery Status 

Local

 reports the local OAM discovery status as follows: 

Remote

 reports the remote OAM discovery status as follows: 

Loopback 

Local

 and 

Remote

Status

 indicates the status of the local and remote loopback: 

Enabled

 represents a Looped-Up condition and 

Disabled

 a 

Looped-Down condition.

Enable

/

Disable

 button allows respectively Looping-Up (

Enable

) 

or Looping-Down (

Disable

).

Status

Description 

Evaluating

OAM discovery is started.

Stable

OAM discovery is completed. Local OAM is satisfied with the remote 
OAM settings.

Unsatisfied

OAM discovery cannot complete successfully.
Local OAM equipment is unsatisfied with the remote OAM settings.

Status

Description 

Evaluating

OAM discovery is started.

Stable

OAM discovery is completed. Remote OAM is satisfied with the local 
OAM settings.

Unsatisfied

OAM discovery cannot complete successfully.
Remote OAM equipment is unsatisfied with the local OAM settings.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands